RON HAZELTON:
Well now, I’m on my way to Lafayette, California, to visit Gena Pardo.
Aha, cabinet doors.
GENA:
These are the cabinets.
RON HAZELTON:
Yeah, those have been there a while huh?
GENA:
Yes, they have.
RON HAZELTON:
So where did you come up with this idea for glass doors?
GENA:
I've seen the look for quite a number of years in magazines that I worked in — that I used to work in.
RON HAZELTON:
Now you realize that there's one problem with glass doors.
GENA:
Yeah. I know, I have to be tidy. [LAUGHS]
I Have to be neat and clean.
RON HAZELTON:
[LAUGHS] Yeah, I think you're right about that.
RON HAZELTON:
So here's what I'm thinking — there are a couple ways we could do this. We could take these doors and cut holes in them and then drop glass in the center, which sounds like it might be easier. But the other way is to actually take the doors off and build brand new doors —frames and then put glass in the center.
I think I'm going to opt for the second way.
GENA:
Okay. And why is that?
RON HAZELTON:
Because it will be a bigger challenge for you.
GENA:
[LAUGHS] Uh oh.
RON HAZELTON:
[LAUGHS] No, I think actually, it's going to be a little bit easier. All right, Gena. I'll use this to take those hinges off.
GENA:
All right.
RON HAZELTON:
I usually like to start at the bottom —
Gena and I begin by removing the old doors.
GENA:
Oh, I love that, how it sticks.
[BOTH TALK AT ONCE]
RON HAZELTON:
The old doors will serve as templates for the new doors we're going to make.
There we are, one down, four to go.
Instead of being solid though, the new doors will be open frames, made from strips of 1 x 3 poplar we've purchased at the home improvement center. Step one is to cut these strips to length.
That's — it looks a little scary but it's really a very, very safe saw to use. It's called a power miter saw. More correctly a sliding compound miter saw. It's got a lot of features on it. We're basically going to use it today just to cut the strips of wood to the proper length, okay?
GENA:
Okay.
RON HAZELTON:
This is a nice feature of the saw. It's a work-stop and if you'll just slide this along here, you'll see that you can read different measurements as you go.
GENA:
Mm-hmm [AFFIRMATIVE].
RON HAZELTON:
So let's start with the sides. So we need eight pieces at 34 inches.
GENA:
All right.
RON HAZELTON:
So I set it right at 34. There you go.
Using the power miter saw this way will insure that matching pieces will end up exactly the same length — essential if we want our doors to be square.
Not bad huh, for your first cut?
GENA:
Wow. I think I'm better with this than I am with a screwdriver [LAUGHS].
RON HAZELTON:
So what we ended up with here are about — how many — 4, 16 pieces of wood, 4 for each door.
We'll be joining these pieces at the corners, using something called a lap joint. At each end, we'll remove half the thickness of the board. When the two pieces are placed together at right angles, the ends will now overlap, forming a very strong joint.
We'll remove the material from the ends using a router.
Well, on both sides of that sort of cylinder, are two cutting bits. There's one right there and one, one right there. And so what we're going to do is, we're going to slide this along the end of these boards right here.
We rout four ends at one time by clamping boards together on a flat surface. Now, Gena gives it a try. It's a little dusty, but after just a few passes with the router, she's got the hang of it.
Very nice, okay?
Now that we've formed the lap joints, we're ready to attach the framed pieces to each other.
Right? 'Cause the first thing we're going to do on these is glue them together.
GENA:
Okay.
RON HAZELTON:
Putting the glue in a shallow can and applying it with a brush, makes it neater and insures an even coating. This is yellow wood glue and we apply it to both surfaces.
We're going to place this one right on top of the other, just like that.
GENA:
Okay.
RON HAZELTON:
Okay? And then I want to make sure that this is square so we'll put the framing square in here.
Small nails or brads, will hold the joint together until the glue dries.
Now, there's our first one.
GENA:
Great.
[BOTH SPEAK AT ONCE]
RON HAZELTON:
First frame, there are three more like this, huh?
GENA:
Terrific.
RON HAZELTON:
Okay, back to your favorite new tool, the router.
GENA:
I know that is.
[BOTH SPEAK AT ONCE]
RON HAZELTON:
Now if you look closely at this, you'll see it's got a curve on it and it has a ball bearing guide —
This bit, called a roundover bit will remove the sharp corner from the edge of the frame, leaving a smooth curved surface.
And since that has a ball bearing, the ball bearing will sort of guide itself around the inside here.
GENA:
All right.
RON HAZELTON:
Okay? So we've rounded over all these edges on the front of the door.
GENA:
Right.
RON HAZELTON:
Now I'm going to turn this over and we're going to do something to the back of the door.
GENA:
Okay.
RON HAZELTON:
'Cause these are going to be glass doors, so we have to create a little step into which the glass can sit. To do this, we switched to yet another router bit. This one is designed to cut rabbits or notches in the edge of the piece of wood.
A ball bearing guide keeps the bit from cutting too deeply into the edge of the lumber. Because it is round, the rabbit bit leaves a small amount of material in the corners, which we remove with a chisel. The outside of the frame will also receive a rabbit, which will allow the door to set slightly inside the cabinet opening.
Our frames are now assembled and machined to accept the glass. First though, we apply a coat of paint. It's much easier to do this now than after the glass is in place. As soon as the paint dries, in goes the glass.
RON HAZELTON:
Now that we've got it in here, we've got to keep it in here. So we're going to use something called a keeper's strip. At least that's what I call it. A little strip of wood that's not painted here, and it just sits right in like that.
GENA:
Great.
RON HAZELTON:
And we're going to keep the wood in place with some of these very small brads. This is called a brad pusher. There's a magnet right there. I'm just going to put this in the end, okay. And then if you could kind of hold that in place, I'm just going to push the brad right into the wood. Four keeper strips, held in place with brads, will hold the glass securely in place.
Well, the doors are finished. All we have to do now is install the hinges and hang them on the cabinets.
I love these colors. They look great in here.
GENA:
Oh, this is just exactly what I wanted.
RON HAZELTON:
You're happy?
GENA:
I love 'em, absolutely the way I wanted it to come out.
RON HAZELTON:
And was it fun actually building them yourself?
GENA:
It was fun. I'm going to have a great sense of accomplishment every time I look at it. It's terrific.
RON HAZELTON:
Okay. Do me a favor?
GENA:
Sure.
RON HAZELTON:
Can I have an autograph for
[BOTH SPEAK AT ONCE]
GENA:
Oh, I'm thrilled, I'm thrilled —